|
|
1.INTRODUCTIONDuring the 2013-14 academic year we began a curriculum evaluation and revision of the B.S. (Optical Engineering) program at Rose-Hulman Institute of Technology [1-3]. This evaluation is a regular periodic process that we setup as part of our accreditation requirements of the Engineering Accreditation Commission (EAC) of ABET [3,4]. At that time, we also needed to address how our program planned to meet the specific program criteria for all Optical, Photonic, and Similarly Named Engineering Programs [4]. One of the issues that arose in evaluating our assessment data related to the laboratory preparation and the student’s confidence in their laboratory skills when the students entered the capstone design course sequence. We also needed to explicitly provide instruction on the basics of opto-mechanics driven by the rearrangement of topics in other courses during the curriculum revision. A common approach to teaching laboratory courses typically proceeds as follows: students are provided with a laboratory manual which details the steps needed to complete the lab; students carry out each experiment moving step-by-step through the provided procedure while keeping a live record of their procedure, data, and analysis in a laboratory notebook which is submitted for grading. While this is a useful approach during the freshman and sophomore year to allow students to become familiar with experimental processes and observe physical and optical phenomena, it does not expose students to the necessary skills needed in a capstone project. Our assessment showed that students did not have confidence in their ability to reason through each step in the procedure. Some students blindly followed the written steps and in many cases missed the entire point of the experiment. We already use project activities and assignments in several courses and we have been especially successful using a project-based approach in our engineering capstone design course sequence [2]. To better prepare the student for the capstone design experience course sequence we decided to develop a project-based laboratory course to be taken during a student’s junior year. This paper describes the development of this course and some lessons learned in teaching this course. 2.COURSE OVERVIEWThe new junior-level course, OE 395 – Optomechanics & Optical Engineering Lab, is scheduled for first (fall) quarter of the junior year. The course is required for students seeking a B.S. degree in Optical Engineering. Enrollment in the course requires completion of three prerequisites: PH 292 – Physical Optics, OE 280 – Geometrical Optics, and OE 295 – Photonics Devices and Systems. The primary objective of the course is to teach students, in a hands-on laboratory environment, how topics from these seemingly disconnected areas of optics actually come together in real optical designs. The course meets a total of four times per week over the 10 week academic quarter: two 1-hour lectures and two 3-hour lab periods. The full course description as it appears in the Rose-Hulman course catalog is shown below. OE 395 – Optomechanics & Optical Engineering Lab – Design, assembly, and alignment ofbench top optical systems. Introduction to experimental techniques in optics. Data collection and analysis. Relevant lecture topics including principles of opto-mechanical design, fold mirrors and prisms, lens and mirror mounting, kinematic mounts, precision adjustments and control. An introduction to the principles of optomechanics are covered during the lecture periods. Homework problems are assigned to reinforce concepts introduced in the lecture and two exams (not comprehensive) are scheduled during the academic quarter to assess student learning. Student performance in this portion of the class represents 40% of their final grade. Topics covered in the lecture portion of the class include:
The main emphasis of the course, however, is on the laboratory experience. A series of introductory directed “refresher” experiments are completed in the first week to help the students who are just returning from their summer break get back into the lab. In the first of these, the students are required to align two mirrors to direct a collimated HeNe beam through a drinking straw placed at a random angle (θ and φ) with respect to the normal of the of the optical table. In the second experiment, the students are required to set up a spatial filter with the HeNe laser to produce a clean high-quality diffraction limited beam (which could be used for interferometry). The third experiment involves setting up and programming a basic Arduino development board to control the output of an LED and input the received signal from a photodetector. Following completion of the introductory experiments, the students begin work on the design projects which comprise the bulk of their laboratory efforts. Four projects in total were developed and are intended to expose the students to topics spanning multiple areas of optical engineering. Table 1 depicts the mapping of the four projects to the four areas of optical engineering specifically designated in the ABET program-specific criteria for Optical Engineering, Photonic Engineering, and similarly named programs [4], and each is discussed further in Section 3. Table 1Mapping of the four OE 395 projects to the four main areas of optical engineering. Successful completion of each project relies on the synthesis of concepts from several of the areas.
Students taking the course are required to keep a laboratory notebook, though the format is not prescribed. The laboratory notebook is reviewed by the course instructors upon the completion of each project and feedback is provided. These notebook checks account for 25% of the students’ final course letter grade. At the end of the academic quarter, a final report is assigned which each student is required to complete on an individual basis. The final report is a manuscript-style (formatted to SPIE specifications) full accounting of a single laboratory project from the academic quarter. The students are not told which project they will need to report on until the last week of class. This approach provides a realistic scenario of what would happen in the field and encourages the students to maintain a well-documented notebook, with complete diagrams, data sets, plots, photographs, and analysis. Each group of two students is provided a kit containing of various optical and opto-mechanical components from which their setup must be designed. The kits include optical posts, post holders, lens and mirror mounts, lens tubes, kinematic translation and rotation stages, uncoated spherical lenses of various focal lengths, aspheric objective lenses, flat and spherical mirrors, diffraction gratings, filters, beamsplitters, apertures, irises, a switchable gain Si photodetector, and a CCD camera. The components for these kits were selected by the faculty to provide a wide diversity of possible solutions to the experimental projects the students are expected to complete. A photograph of one of the kits is shown in Figure 1 and a complete listing of the kit contents is provided in Table 2. All parts were supplied by Thorlabs, Inc. [5] and the total cost for each kit is ~$5000. Optical sources included 5 mW HeNe lasers, 5 mW 635 nm diode laser sources, and halogen which light sources are also provided for use, and instrumentation such as oscilloscopes, digital multimeters, and computers are also made available. Table 2- Complete listing of the contents of the kit provided to the students in the course.
3.LABORATORY PROJECTS3.1Project #1 – Absorption SpectroscopyThe absorption spectroscopy project was developed to combine concepts in first-order geometrical optics design with diffraction effects studied in physical optics. The project assignment, as provided to the students, is detailed in Table 3. The students are presented with a problem of measuring the absorption spectrum of a common organic dye. Note in the project assignment, very little guidance is provided on how the students might best to utilize the kit components to build a functioning system. Specifications such as wavelength accuracy and necessary bandwidth are left vague, and students are expected to develop appropriate specifications in response. Each team is expected to develop a first-order model to estimate their system bandwidth by applying the principles of geometrical optics combined with the grating equation. Students expend significant effort researching basic spectrometer designs and understanding the role first-order design choices (such as entrance and exit aperture sizes and lens/mirror focal lengths) have on the resolution of the system. Table 3- Absorption spectroscopy project assignment.
Figure 2 and Figure 3 present sample work taken from one team’s project notebook. Figure 2 depicts a schematic layout of the team’s final optical design. The team used use a hand-made paper slit as the entrance slit for the system. A 100 mm effective focal length lens collimates the light from the plane of the slit and directs it onto the diffraction grating. Two 50 mm lenses provided in the kit were combined to serve as a 25 mm EFL focusing lens (which was not available in the kit) to image the dispersed slit on the CCD camera serving as a quasi-1D detector array for the spectral measurement. Figure 3 (Left) depicts a photograph of the same team’s final setup. It is worth noting that this team was the only to use the CCD camera; the other three project teams this year elected to instead utilize the single photodetector with exit slit, and by rotating the grating, scan individual wavelengths. We believe that the approach of providing minimal guidance in the project assignment gives students the experiences exploring a diverse solution space. At right in Figure 4 is the team’s measured transmission spectrum. These results were achieved by analyzing an image file output by the camera to determine the line intensity profile of one row of pixels. Several issues were encountered during the execution of this first project. None of the groups directly measured the resolution of their system to compare to the calculated values. While this wasn’t explicitly stated in the project statement, such verification of calculations is commonly expected of design engineers and in this case, it provided an excellent learning opportunity. Only one of the four teams actually developed a proper calibration process (wherein a source of known wavelength was measured to confirm wavelength calibration). Several groups failed to provide a plot directly comparing their output to the output of the spectrophotometer. These shortcomings led to a debriefing process which was implemented after each of the subsequent projects. In each case, the student teams discussed areas of potential improvement, missing results, and better methods for presenting their design results in a clear manner. 3.2Project #2 – Refractive Index of AirThe goal of the second project was to develop an experimental instrument to measure the refractive index of air. This project draws on the fundamentals of interferometry (a central topic to physical optics) combined with first-order optical design in order to achieve an appropriate result. Each student team developed a Michelson interferometer of varying dimensions and inserted an optical cell in one branch which could be evacuated. A photodetector at the exit plane is was commonly used by the student teams to assist in the counting of interference fringe changes as air is allowed to slowly bleed back into the optical cell. With knowledge of the cell dimensions and number of fringe changes between the evacuated cell and air-filled cell, the refractive index of air can be calculated with remarkable precision. While the general technique is clearly described, the development of appropriate mathematical model and complete optical design is again left completely up to the student. Table 4 provides the complete project assignment. Table 4- Refractive index of air project assignment.
Figure 4 and 5 present sample work taken from one team’s project notebook. A schematic diagram of the basic optical layout and as well as a photograph of the final setup for the team is shown in Figure 4. This team utilized a HeNe laser without the use of a spatal filter as the source. A beam expansion lens is used to adjust the collimated beam diameter at the detector plane. The beam is split (50:50) and each leg is reflected off a planar mirror. The careful alignment necessary to achieve a clear centered interfernce pattern at the detector plane was one of the more difficult aspects of the project. All four teams worked on the same optical bench making unintentional vibrations caused by others difficult to overcome. This project team monitored the photodetector output on an oscilloscope set to capture data over a long time period. The cell was first evacuated then data capture was started and a valve was slightly opened to allow air to slowly refill the cell (this approach eliminated the vibrations caused by the vacuum pump which caused significant noise in the measurement). Figure 5 presents one of the photodetector measurements vs. time (note the students terminated this test early, and likely failed to count the proper number of fringes). The team’s data table from several tests is shown at right in Figure 5, with N denoting the number of fringes counted, and n referring to the refractive index of air at room temperature. The final reported value for the refractive index of air by this team was 1.00018 while the accepted value at room temperature is 1.00028; the student team correctly identified that the pump used in the experiment was unable to maintain a sufficiently low pressure for closer agreement. 3.3Project #3 – Speed of LightIn the third project, the students measured the speed of light in air using a direct time-of-flight based technique. This approach relies on the linear relationship between the observed phase shift modulated diode laser beam at the receiver and the distance through which the collimated beam travels before striking a photodetector. This experiment combines topics from the photonics (laser diode sources, detectors) with practical aspects of geometrical optics (such as achieving a sufficient degree of collimation of the beam to detect light after a significant propagation distance). The experiment is further constrained in that the students are limited to a work area approximately 5ft x 2 ft in dimension. Table 4 lists the project assignment as provided to the students. Table 5- Speed of light project assignment.
Figure 6 and 7 present sample work taken from one team’s project notebook. At left in Figure 4 is a schematic drawing of the students’ experimental setup and at right is a photograph of the oscillsocope showing the modulated source voltage and the photodetector output. One o Figure 7 depicts a plot of the propagation distance as a function of the measured phase delay. The slope of the line (in this case 2.97 ± 0.08 x108 m/s) gives the speed of light. One of the primary issues encountered by several teams in this experiment was a failure to identify that the phase shift at zero distance would still be nonzero. Several teams incorrectly calculated the speed of light from a single point measurement – dividing the propagation distance by the observed phase difference at that point. 3.4Project #4 – Camera LensThe last project in this course is the design and construction of a lens system for the ThorLabs DCC1545M CMOS camera. As shown in Table 6, there are several specifications that must be met and tested related to camera field-of-view but the design is open-ended with numerous possible solutions. The major constraint is that the lenses used in the design must be parts from the lab kit. Figure 8 shows a pictorial representation of the layout and a photograph of one of the student’s designs. It is important to note that all student groups did perform a first-order layout in their preliminary design calculations. We decided to ask for contrast transfer function (CTF) measurements rather than a modulation transfer function (MTF) to simplify the experiment and to allow for students to identify and specify a test target (Figure 9). The camera software application allows for line profiles to be captured from an image and this is what was used to obtain data for the CTF as shown in Figure 10 with the resulting CTF of Figure 11. All students in the class appreciated the synthesis of topics from physical optics, geometrical optics, and photonic devices courses. Table 6- Camera Lens Assignment
4.CONCLUSIONEvaluations of this course from this cohort of students were positive but also provided several constructive comments for improvement. This year we plan to better integrate the opto-mechanics topics from the lecture with the project schedule. For example, several students proposed using Foucault’s method and we plan to try and incorporate this measurement as a second method for measuring the speed of light. This same student cohort just completed the first course of their capstone design experience during the spring quarter 2016 [2]. One observation noted by the course instructors was that every student team successfully demonstrated a working design for every project which had never been the case for past classes. Further assessment of student confidence in their ability and skills in the laboratory will be performed as this cohort of students completes their capstone design course sequence this academic year. ACKNOWLEDGEMENTSThe authors would like to thank Daniel K. Lauriola and Jacob D. Tyler for granting permission to use their coursework as examples of student submissions in this paper. ReferencesR. M. Bunch, C. H. Joenathan, and A. Z. Siahmakoun,
“From optics to optical engineering: 20 years of optics education at Rose-Hulman Institute of Technology,”
presented at the Education and Training in Optics and Photonics,
(2003). Google Scholar
R. M. Bunch, P. O. Leisher, and S. C. Granieri,
“Optical engineering capstone design projects with industry sponsors,”
in Proc. of SPIE,,
(2014). Google Scholar
P. O. Leisher, S. C. Granieri, R. M. Bunch, A. Siahmakoun, and C. Joenathan,
“Curriculum revisions for meeting the new ABET program-specific criteria in optical engineering,”
979321
–979321-8
(2015). Google Scholar
Available:ABET Criteria for Accrediting Engineering Programs.,”
http://www.abet.org/wp-content/uploads/2015/04/E001-14-15-EAC-Criteria.pdf Google Scholar
|