Dr. Anna Okunkova Profile

Dr. Anna Okunkova

Senior Researcher at Moscow State Univ of Technology "STANKIN"

SPIE Involvement:

Author

Publications (4)

Proceedings Article | 12 September 2021 Presentation + Paper

Real-time monitoring of wire electro-discharge machining semiconducting composite ceramics TiC+Al2O3

Mikhail Kozochkin, Anna Okunkova, Artem Ershov, Marina Volosova, Artur Porvatov, Alexsander Zelensky, Alexsey Nadykto, Petr Pivkin

Proceedings Volume 11867, 1186709 (2021) https://doi.org/10.1117/12.2602168

KEYWORDS: Ceramics, Electrodes, Semiconductors, Control systems, Composites, Adaptive control, Resistance, Signal processing

Read Abstract +

Proceedings Article | 12 September 2021 Presentation + Paper

A new method for efficiently controlling energy use in Electrical Discharge Machining (EDM)

Sergey Grigoriev, Artur Porvatov, Mikhail Kozochkin, Ilya Minin, Anna Okunkova, Marina Volosova, Vladimir Kuptsov, Petr Pivkin

Proceedings Volume 11867, 118670A (2021) https://doi.org/10.1117/12.2602169

KEYWORDS: Electrodes, Dielectrics, Control systems, Liquids, Signal processing, Manufacturing, Power supplies, Explosives

Read Abstract +

Rationalizing energy consumption in the Electrical Discharge Machining (EDM) efficiently saves energy and improves machining quality. Since the conventional methods for estimating useful EDM energy are based on theoretical heat transfer studies or empirical assessments of processing conditions, the development of an industrially applicable method for assessing useful energy is an important problem. Here we show that the performance of the EDM process is directly related to acoustic emission (AE). The effectiveness of the proposed method has been evaluated in experiments. As part of the execution of the experiment, AlCuMg1 workpiece was machined using a copper electrode with different duty cycles with pulse widths varying from 10% to 80%. For comparative analysis, the root-mean-square vibroacoustic signal in the range of 1-10 kHz and the root-mean-square of the discharge current were used. It was found that the amplitude of the vibroacoustic (VA) signal monotonically increases with the increasing EDM performance. The properties of the VA signal allows using the VA monitoring to assess the performance of EDM, i.e., to determine the fraction of energy spent on removing the workpiece material. The advantage of the proposed method of monitoring is that the control of useful energy is carried out using accelerometers installed on the parts of the technological system on the workpiece side. The distance from accelerometers to the workpiece being processed can be quite large that is convenient for performing experiments. In particular, in the high frequencies range, the obtained results are protected from mechanical interference coming from drives, hydraulic units and wire rewinding mechanisms. Such VA signals are shown to be important indicators of EDM efficiency because they are observed only if the energy fluxes reach the workpiece surface. This provides a more reliable indication of raising concentrations of electroerosion products that prevents short circuits and breakage of wire electrodes.

Proceedings Article | 1 August 2021 Poster + Paper

Electrically conductive nanocomposite films deposition and electrical discharge machining of ceramic surfaces to generate functional microtextures

Marina Volosova, Anna Okunkova, Sergey Fedorov, Enver Mustafaev, Khaled Hamdy

Proceedings Volume 11802, 118020R (2021) https://doi.org/10.1117/12.2593968

KEYWORDS: Ceramics, Nanocomposites, Electrodes, Optical coatings, Aluminum, Titanium, Multilayers, Tin, Spectroscopy, Optical microscopy, Aluminum nitride

Read Abstract +

Proceedings Article | 1 May 2014 Paper

Laser-beam modulation to improve efficiency of selecting laser melting for metal powders

A. Okunkova, P. Peretyagin, Yuri Vladimirov, M. Volosova, R. Torrecillas, S. Fedorov

Proceedings Volume 9135, 913524 (2014) https://doi.org/10.1117/12.2053602

KEYWORDS: Spatial light modulators, Modulation, Gaussian beams, Metals, Tolerancing, Additive manufacturing, Amplitude modulation, Laser sintering, Rapid manufacturing, Prototyping

Read Abstract +

View contact details

UPDATE YOUR PROFILE

Is this your profile? Update it now.

Sign into your SPIE.org account

Don’t have a profile and want one?

Create an account on SPIE.org

Keywords/Phrases

Search In:

Publication Years