Stable local oscillators with low phase noise are extremely important elements in high performance military
communication and navigation systems. We present the development of compact UHF-band frequency sources capable
of maintaining low phase noise under high accelerations or vibrations and over a wide temperature range for handheld
portable systems. We also explored nonlinearity in MEMS resonators and attempted to use nonlinear dynamics to
enhance phase noise performance. Using the quartz MEMS technology, we have thus far demonstrated a 645 MHz
Pierce oscillator with -113 dBc/Hz phase noise at 1 kHz offset with acceleration sensitivity of 5x10-10/g. The controlled
oscillation of a nonlinear Duffing resonator in a closed-loop system with improved phase noise is described.
A W-band unamplified direct detection radiometer module is described that provides a wideband response and is
scalable to large arrays. The radiometer design is intended to provide sufficient sensitivity for millimeter wave imaging
applications with a goal of 2K noise equivalent temperature difference (NETD) at a 30 Hz frame rate.
This effort leverages previously reported device scaling to increase sensitivity. We present a radiometer module
designed for 60 GHz RF bandwidth that utilizes HRL's antimonide-based backward tunnel diode. An impedance
matching circuit with on- and off-chip elements, as well as ridged waveguide, provides a wideband match to the
detectors. Modules were designed with two different microwave substrates: 125 micron thick quartz and 100 micron
thick alumina. flip-chip bonding of the detectors is amenable to automated pick-and-place for high volume
manufacturing. The modular nature of the array approach allows large arrays to be manufactured in a straightforward
manner. We present the design approach along with both electromagnetic simulations and measured performance of the
modules. This work was supported by phase II of DARPA's MIATA program.
We are developing a passive W-band millimeter wave imaging array that operates without the use of RF low noise
amplifiers. The work is supported by the DARPA MIATA program. Previously reported Phase I results were a noise
equivalent temperature difference (NETD) of 4.8°K. The goal of Phase II, currently underway, is to decrease this to 2°K
or less. There are two improvements that must be made to achieve the goal. The square law diode detector sensitivity
and the RF bandwidth reaching the detector must be increased significantly. This paper mainly deals with the first issue,
the effort to increase the sensitivity by decreasing the diode area and capacitance, using electron beam lithography.
Brief mention will be made of the redesign of the antenna-to-diode transition that simulations indicate will provide a
doubling of bandwidth from 30 to 60 GHz.
Sb-heterostructure diodes have become the detector of choice for W-band millimeter wave imaging cameras now
being commercialized or in prototype development. Here we optimize the diode impedance to yield a minimum noise equivalent
power (NEP). The goal is to decrease the gain required of the front-end LNA. Measured W-band sensitivities for two diodes are
3500 and 5500V/W. Their zero bias differential resistance values imply Johnson noise limited NEP's of 0.98 and 0.83pW/Hz1/2,
respectively, much less than obtained from conventional biased Schottky diodes. A MMIC version of the diode detector has been
simulated with an integrated bandwidth of ~ 30 GHz at W-band. The simulated temperature sensitivity (NEΔT) with an HRL W-band
LNA on the front end is <1°K.
We have demonstrated a high efficiency package for zero bias Sb-based backward tunnel diodes developed for passive millimeter wave imaging. Flip-chip mounting of detector MMICs onto quartz substrates permit placement of the detector directly within the WR-10 waveguide feeds for diagonal horn antennas. This arrangement minimizes the losses between the detectors and antennas while providing an impedance match over a majority of W band. A 2x2 array of radiometers was fabricated, assembled, and measured using coherent measurement techniques. The resulting noise equivalent temperature difference, calculated assuming a 30 Hz frame rate is 10 degrees K.
The figure of merit for RF detectors, noise-equivalent power (NEP), is determined by the noise divided by the sensitivity. Thus, the challenge is to design a diode structure that has low junction resistance while maintaining a large nonlinearity. This work presents sensitivity and noise measurements for Sb-heterostructure backward diodes with varying barrier thicknesses and cross-sectional areas. Nominal diode areas are 2x2mm2 and 3x4mm2 with 15Å and 20Å barriers. The best NEP measured to date is 1.19 pW/rtHz at 36.5 GHz.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.