In this paper, we demonstrate for the first time the far-field experimental results and the linewidth characteris-
tics for widely tunable surface-micromachined micro-electro-mechanical system (MEMS) vertical-cavity surface-
emitting lasers (VCSELs) operating at 1550 nm. The fundamental Gaussian mode emission is confirmed by
optimizing the radius of curvature of top distributed Bragg reflector (DBR) membrane and by choosing an ap-
propriate diameter of circular buried tunnel junctions (BTJs) so that only the fundamental Gaussian mode can
sustain. For these VCSELs, a mode-hop free continuous tuning over 100 nm has already been demonstrated,
which is achieved by electro-thermal tuning of the MEMS mirror. The fiber-coupled optical power of 2mW over
the entire tuning range has been reported. The singlemode laser emission has more than 40 dB of side-mode
suppression ratio (SMSR). The smallest linewidth achieved with these of MEMS tunable VCSELs is 98MHz
which is one order of magnitude higher than that of fixed-wavelength VCSELs.
We present surface micro-machined micro-electro mechanical-system (MEMS) tunable vertical-cavity surfaceemitting
lasers (VCSEL) with rectangular and triangular shaped quantum wells (QWs) emitting around 1:95 μm
predestined for broadband tunable diode laser absorption spectroscopy. The VCSELs show single-mode operation
and high side-mode suppression-ratio SMSR < 50 dB within the whole tuning range of 50nm and 35 nm, the
fibre-coupled optical power of 1:0mW and 1:76mW and the threshold current of 2:5mA and 2:0mA for the
rectangular and triangular shaped QWs respectively. The 3 dB modulation frequency of the MEMS is 110 Hz.
A mode hop free single mode tuning < 90nm at 40°C and 45nm at 70°C is demonstrated with a MEMS tunable VCSEL for the first time. The device shows a fiber-coupled output power of 2.9mW at 20°C and 0.5mW at 70°C. The side mode suppression ratio is larger than 40 dB over the entire tuning and temperature range of up to 70°C. The presented technology is cost effective and thus capable for mass production. It is applicable for tuneable VCSELs operating in different wavelength regimes, which are limited by the absorption of the DBR materials only.
The latest results on InP based 1550 nm short-cavity VCSELs will be presented. Important design criteria will be
discussed in order to manufacture high-power, high-speed or widely tunable VCSEL devices, respectively.
We present a micro electro-mechanical system (MEMS) tunable vertical-cavity surface-emitting laser (VCSEL) emitting
around 1.55 μm with single-mode output power of >2.5mW and high side-mode suppression-ratio (SMSR) of >50dB
over the entire tuning range of >50nm. The small-signal modulation technique (S21) has been used to study intrinsic and
parasitic influences on the modulation response of the device. Additionally, the static characteristics as well as electrical
and thermal design of the device are discussed with respect to its high-speed modulation behavior. The tunable laser
shows 3-dB direct modulation frequencies above 6.4 GHz.
We report the investigation of the state of polarization (SOP) of a tunable vertical-cavity surface-emitting laser
(VCSEL) operating near 850 nm with a mode-hop free single-mode tuning range of about 12 nm and an amplitude
modulation bandwidth of about 5 GHz. In addition, the effect of a sub-wavelength grating on the device and
its influence on the polarization stability and polarization switching has been investigated. The VCSEL with an
integrated sub-wavelength grating shows a stable SOP with a polarization mode suppression ratio (PMSR) more
than 35 dB during the tuning.
We present surface micro-machined tunable vertical-cavity surface-emitting lasers (VCSELs) operating around
1550nm with tuning ranges up to 100nm and side mode suppression ratios beyond 40 dB. The output power
reaches 3.5mW at 1555 nm. The electro-thermal and the electro-statical actuation of a micro electro-mechanical
system (MEMS) movable distributed Bragg reflector (DBR) membrane increases/decreases the cavity length
which shifts the resonant wavelength of the cavity to higher/lower values. The wavelength is modulated with
200 Hz/120 kHz. Both tuning mechanisms can be used simultaneously within the same device. The newly
developed surface micro-machining technology uses competitive dielectric materials for the MEMS, deposited
with low temperature plasma enhanced chemical vapor deposition (PECVD), which is cost effective and capable
for on wafer mass production.
Widely tunable vertical cavity surface emitting lasers (VCSEL) are of high interest for optical communications,
gas spectroscopy and fiber-Bragg-grating measurements. In this paper we present tunable VCSEL operating at
wavelength around 850 nm and 1550 nm with tuning ranges up to 20 nm and 76 nm respectively. The first versions
of VCSEL operating at 1550 nm with 76 nm tuning range and an output power of 1.3mW were not designed for
high speed modulation, but for applications where only stable continious tuning is essential (e.g. gas sensing).
The next step was the design of non tunable VCSEL showing high speed modulation frequencies of 10 GHz with
side mode supression ratios beyond 50 dB. The latest version of these devices show record output powers of
6.7mW at 20 °C and 3mW at 80 °C. The emphasis of our present and future work lies on the combination of
both technologies. The tunable VCSEL operating in the 850 nm-region reaches a modulation
bandwidth of 5.5GHz with an output power of 0.8mW.
We present 1.55 μm short-cavity buried-tunnel-junction VCSELs (Vertical-Cavity Surface-Emitting Lasers) with single
mode output powers of 6.7 mW at 20°C and 3 mW at 80°C, respectively. Although the device had been predominantly
optimized for high-power applications and a proper heat management, we are also observing a 3dB-cut-off frequency of
more than 11 GHz and side mode suppression ratios (SMSRs) beyond 54 dB over the whole temperature range. The
tuning range of the devices can be increased from 7 nm based on gain tuning to several tens of nanometers when
replacing the top DBR by a micro-electro-mechanical system (MEMS) distributed Bragg reflector (DBR) composed of
semiconductor or dielectric material being thermally actuated for changing the cavity length. These devices are perfectly
suitable for telecommunication and gas sensing applications and represent outstanding devices for the so called tunable
diode laser absorption spectroscopy (TDLAS) technique.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.