Significant development has been made on phosphorescent organic light emitting diodes (PHOLEDs) over
the past decade, which eventually resulted in the commercialization of widely distributed active-matrix organic light
emitting diode displays for mobile phones. However, higher efficiency PHOLEDs are still needed to further reduce
the cost and lower the power consumption for general lighting and LED backlight applications. In particular, red
PHOLEDs currently have in general the lowest efficiencies among the three primary colors, due most likely to the
energy-gap law. Therefore, a number of groups have of made use of various device configurations, including
insertion of a carrier blocking or exciton confining layer, doping the transport layers, as well as employing multiple
emissive zone structures to improve the device efficiency. However, these approaches are rather inconvenient for
commercial applications. In this work, we have developed a simpler way to boost the performance of red PHOLEDs
by incorporating an exciton harvesting green emitter, which transfers a large portion of the energy to the co-deposited
red emitter. A high external quantum efficiency (EQE) of 20.6% was achieved, which is among the best
performances for red PHOLEDs.
The development of high performance organic light emitting diodes (OLEDs) for display and lighting
applications has attracted considerable research interest from both academia and industry. In this work, the
designs of simplified phosphorescent OLEDs with exceptionally high efficiency are discussed. It is found
that discrete blocking layers and a double emission zone are unnecessary to achieve high efficiency in
optimized phosphorescent OLEDs. Due to the elimination of these redundant layers, the device structure can
be highly simplified. It is also shown that single-layer, two organic component devices are feasible with
state-of-the-art efficiency.
A major barrier to commercial adoption of organic light emitting diode (OLED) based devices is
their often unacceptably fast rate of degradation. Typically, to estimate device lifetime, electrical
parameters such as driving voltage and luminance are periodically measured while constant
current is applied to the OLED. Due to the repetitive nature and long timescales involved in
lifetime testing, the procedure is an ideal candidate for automation. An automated lifetimetesting
system and accompanying software was developed to simultaneously drive multiple
OLED devices and collect lifetime parameters while the entire system is under ultra-high
vacuum conditions. The system is connected to a larger vacuum chamber so that devices can be
synthesized and then analyzed in situ without exposure to atmosphere. The system was
developed with the aim of facilitating rapid discovery and understanding of OLED degradation
mechanisms.
Non-blocking Phosphorescent Organic Light Emitting Diode (NB-PHOLED) is a highly simplified device structure that
has achieved record high device performance on chlorinated ITO[1], flexible substrates[2], also with Pt based
phosphorescent dopants[3] and NB-PHOLED has significantly reduced efficiency roll-off[4]. The principle novel
features of NB-PHOLED is the absence of blocking layer in the OLED stack, as well as the absence of organic hole
injection layer, this allows for reduction of carrier accumulation in between organic layers and result in higher
efficiencies.
This paper presents our research and development efforts in realizing and perfecting organic/inorganic photon
upconversion devices for wavelengths from near infrared (1.5 μm) region to visible light (green). The basic idea is to
integrate an InGaAs/InP photodetector with an organic light emitting diode (OLED), connected in series. The detected
photocurrent drives the OLED to emit visible light, thereby achieving the wavelength conversion. We have adopted new
strategies to improve the external device efficiency, including insertion of an embedded mirror and integration of a
heterojunction phototransistor (HPT) and an OLED. As a result, infrared optical upconversion is demonstrated at room
temperature with a built-in electrical gain of 15 from the HPT and an external upconversion efficiency that is improved
by one order of magnitude.
The band alignment at metal-organic interfaces has been extensively studied; however the electrodes in real devices
often consist of metals modified with dielectric buffer layers. We demonstrate that interface dipole theory, originally
developed to describe Schottky contacts at metal-semiconductor interfaces, can also accurately describe the injection
barriers in real organic electronic devices (i.e, at
electrode-organic interface). It is found that theoretically predicted
hole injection barriers for various archetype metal-organic and
metal-dielectric-organic structures are in excellent
agreement with values extracted from experimental measurements.
This paper presents our research and development efforts in realizing and perfecting organic/inorganic photon
upconversion devices for wavelengths from near infrared (1.5 μm) region to visible light (green). The basic idea is to
integrate an InGaAs/InP photodetector with an organic light emitting diode (OLED), connected in series. The detected
photocurrent drives the OLED to emit visible light, thereby achieving the upconversion. A few approaches of integration
methods and device designs have been tested.
Fullerene (C60) has been found to form a universal hole injection interface in the Metal/C60 anode structure. This bilayer structure opens up possibilities to select various highly conductive metals as anodes to replace indium tin oxide (ITO).
Organic light emitting diodes (OLEDs) utilizing Au/C60 and Mg/C60 bilayer anodes were fabricated.
Electroluminescence (EL) efficiencies of devices with Au/C60 anodes surpassed the ITO baseline device by ~ 25%. It was found that the hole injection current for the Au/C60 anode can be tuned via the C60 interlayer thickness in the range of 1 - 5 nm. Single carrier
hole-only (HO) devices with different metal and metal/C60 bilayer anodes were studied. With
the insertion of a 3 nm thick C60 buffer layer between the anode metal and hole transport layer (HTL), an increase in hole
injection current of more than two orders was realized. Based on device modeling we extracted C60-induced dipoles on
the metal surfaces. These dipole values agree well with values obtained by Kelvin probe and photoemission
measurements. What is more, the dipole values effectively pin the work function of all metals to a common value of ~ 4.6 eV, creating a universal hole injection barrier regardless of the pristine anode metal work function.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.