Mr. SungHun Lim Profile

SungHun Lim

at SK Hynix Inc

SPIE Involvement:

Author

Publications (3)

Proceedings Article | 10 April 2024 Presentation + Paper

The importance of less damaged and surface sensitive metrology to identify true EUV process monitoring

GwangSeob Lim, EunKyeong Jang, BoGyeong Choi, Jihyun An, MinWoo Kang, Sunghun Lim, Jong-Hoi Cho, Daiyoung Mun, Ran Alkoken, Tal Vol, Yana Branzburg, You Jin Kim, Jeong Ho Yeo, KyungJae Choi, Kyeongju Han, Sujin Lim, Jaemin Cho, JaeEun Lim, WooSung Jung, Chanhee Kwak, Hyeon Sang Shin

Proceedings Volume 12955, 1295517 (2024) https://doi.org/10.1117/12.3012913

KEYWORDS: Shrinkage, Etching, Extreme ultraviolet, Photoresist materials, Metrology, Semiconducting wafers, Extreme ultraviolet lithography, Photoacid generators, Stochastic processes, Critical dimension metrology

Read Abstract +

The adoption of EUV technology in DRAM fabrication is primarily driven by the pursuit of higher device densities, improved performance, and increased energy efficiency. EUV's shorter wavelength (13.5 nm) enables enhanced resolution and finer patterning, enabling the production of smaller memory cells with reduced feature sizes. As the target patterning size is becoming sub-10nm, line edge/width roughness (LER/LWR) is the centerpiece in controlling uniformity of pattern going through the lithography process. Accordingly, it is essential to figure out the dedicated CDSEM metrology method for EUV step without any image quality degradation, charging issue, and e-beam damage that can hinder accurate diagnosis of the real process status. Empirically, it is highly difficult to predict the best metrology condition that fits to the specific resist material, dimension, and geometry due to complex stochastic effect caused by secondary electron inside photoresist (PR) material. Here we represent experimental results of PR damage caused by electron beam irradiation with different landing energy for both line and space (LS) pattern and contact hole (CH) pattern. The results enabled us to define the effect of the landing energy and geometry of pattern on the critical dimension (CD) and roughness. We examined electron irradiation induced damage by comparing etch bias of fresh location and e-beam exposed location on etch process step to fully understand shrinkage and deformation behavior. For the roughness measurement of CH pattern, we adopted new metric which enables us to quantify contact edge roughness and shape of contact. Utilizing various metrics, it was possible to observe damage on the process, which was not observed only by CD changes, and it was confirmed that the primary beam with low landing energy could be used to not only reduce damage but also enhance surface sensitivity of metrology without bias which is crucial for stochastic effect monitoring on the EUV process.

Proceedings Article | 27 April 2023 Poster + Paper

Tracing optimized condition for electron beam metrology of EUV photoresist pattern using low-landing energy

Woosung Jung, Jong-Hoi Cho, SungHun Lim, TaeSeop Lee, DaeYoung Choi, Jong-Hyun Seo, SeungHyun Lee, JunKyoung Lee, You Jin Kim, Jeong Ho Yeo, Alex Brikker, Roi Meir, Ran Alkoken, Kyeongju Han, Sujin Lim, KyungJae Choi, Chanhee Kwak, Hyeon Sang Shin

Proceedings Volume 12496, 124963E (2023) https://doi.org/10.1117/12.2660114

KEYWORDS: Shrinkage, Photoresist materials, Extreme ultraviolet lithography, Critical dimension metrology, Photoacid generators, Metrology, Electron beams, Etching, Outgassing, Lithography

Read Abstract +

Proceedings Article | 27 April 2023 Poster + Paper

Tracing optimized condition for electron beam metrology of EUV photoresist pattern using low landing energy

Proceedings Volume 12496, 1249622 (2023) https://doi.org/10.1117/12.2660118

KEYWORDS: Shrinkage, Photoresist materials, Extreme ultraviolet lithography, Critical dimension metrology, Photoacid generators, Metrology, Extreme ultraviolet, Etching, Electron beams, Outgassing

Read Abstract +

View contact details

UPDATE YOUR PROFILE

Is this your profile? Update it now.

Sign into your SPIE.org account

Don’t have a profile and want one?

Create an account on SPIE.org

Keywords/Phrases

Search In:

Publication Years